Plumbing for Beginners: What You Need for Installing a Bathtub
Plumbing for Beginners: What You Need for Installing a Bathtub
Blog Article
We've stumbled upon the article involving A Step-by-Step Guide to Installing a Bathtub below on the web and accepted it made sense to share it with you on this page.
Mounting a bathtub isn't exactly rocket science, however it does need solid plumbing, carpentry, as well as sometimes, tiling skills. Changing an old bathtub with a new one is likewise a reasonably difficult job. If the old bathtub is conveniently easily accessible, the project can relocate immediately; if you need to open a wall to remove the old tub and place the brand-new tub, the task is much harder. In either case, the task is within a house handyman's abilities, although you will need a helper to vacate the old tub and embeded in the brand-new one. Ensure you have qualified on your own for the work as well as fit attempting it. As opposed to employing a specialist to take over a halfway-completed task, it is much better to consider using one before you start. Possibilities are you might need a specialist plumber to make tube connections.
This write-up will aid you set up a brand-new bathtub in your washroom if you have currently acquired a new bathtub and also don't need to transform the arrangement of your previous water system pipelines.
Your tools and material list need to comprise the following:
Planning for the Installment
To start with, the sustaining structure provided with the bath should be fitted (if required) according to the manufacturer's instructions. Next, fit the taps or mixer to the bath tub. When suitable the tap block, it is essential to make sure that if the tap features a plastic washer, it is fitted in between the bath as well as the taps. On a plastic bath, it is likewise reasonable to fit a sustaining plate under the faucets unit to prevent stress on the tub.
Fit the versatile tap adapters to the bottom of the two taps utilizing 2 nuts as well as olives (often provided with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet hole, and then pass the electrical outlet via the hole in the bathroom. Utilize the nut supplied by the manufacturer to fit the plug-hole. Examine the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
Next, fit completion of the adaptable overflow pipe to the overflow outlet. Afterwards, screw the pipe to the overflow face which should be fitted inside the bathroom. Ensure you make use of every one of the supplied washing machines.
Connect the catch to the bottom of the waste outlet on the bath tub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, and screw on the catch to the outlet. Connect all-time low of the overflow tube in a similar manner.The bath need to now prepare to be suited its final setting.
Removing Old Touches
If you need to replace old faucets with new ones as a part of your installation, then the first thing you must do is separate the water supply. After doing so, turn on the faucets to drain pipes any water continuing to be in the system. The process of eliminating the existing faucets can be quite problematic as a result of the limited gain access to that is frequently the instance.
Utilize a container wrench (crowsfoot spanner) or a tap device to undo the nut that links the supply pipelines to the taps. Have a fabric all set for the staying water that will certainly originate from the pipes. As soon as the supply pipelines have been eliminated, make use of the very same tool to loosen the nut that holds the taps onto the bath/basin. You will certainly require to quit the single taps from turning during this process. When the faucets have been removed, the holes in the bath/basin will certainly have to be cleaned of any kind of old sealing substance.
Before moving on to fit the brand-new taps, contrast the pipe links on the old taps to the brand-new faucets. If the old faucets are longer than the new taps, then a shank adapter is needed for the brand-new faucets to fit.
Mounting the Bath tub
Utilizing both wood boards under its feet, place the bathtub in the called for setting. The wooden boards are useful in uniformly spreading the weight of the bath tub over the area of the boards as opposed to concentrating all the weight onto four small factors.
The following objective is to make sure that the tub is leveled all round. This can be achieved by checking the spirit level and also adjusting the feet on the bathtub until the spirit level reads degree.
To mount taps, fit all-time low of the furthest flexible tap port to the ideal supply pipeline by making a compression join; after that do the very same for the other faucet.
Turn on the supply of water as well as inspect all joints and also new pipework for leakages and tighten them if required. Load the bathtub and additionally check the overflow outlet and the typical outlet for leakages.
Finally, take care of the bathroom paneling as defined in the producer's user's manual. Tiling and also securing around the bath tub needs to wait until the bathtub has actually been made use of at the very least when as this will settle it into its final placement.
Suitable New Taps
If the tails of the new faucets are plastic, then you will certainly need a plastic adapter to prevent damage to the string. One end of the connector fits on the plastic tail of the tap as well as the various other end provides a link to the existing supply pipes.
If you require to fit a monobloc, after that you will require reducing couplers, which attaches the 10mm pipe of the monobloc to the conventional 15mm supply pipe.
Next, position the tap in the installing opening in the bath/basin making certain that the washing machines remain in area in between the faucet and also the sink. Safeguard the faucet in position with the maker given backnut. As soon as the faucet is safely in place, the supply pipes can be connected to the tails of the taps. The taps can either be attached by using corrugated copper piping or with regular faucet ports. The previous type needs to be connected to the faucet finishes first, tightening only by hand. The supply pipes can later be connected to the other end. Tighten up both ends with a spanner after both ends have actually been attached.
Tiling Around the Bath tub
In the location where the bath meets the tile, it is essential to secure the accompanies a silicone rubber caulking. This is very important as the fitting can move sufficient to fracture a stiff seal, causing the water to pass through the wall surface between the bathroom as well as the tiling, leading to difficulties with moisture and also possible leakages to the ceiling below.
You can pick from a variety of coloured sealers to blend in your components and also fittings. They are offered in tubes and cartridges, and are capable of securing voids up to a width of 3mm (1/8 inch). If you have a bigger gap to fill up, you can fill it with twists of drenched paper or soft rope. Keep in mind to constantly load the bath tub with water prior to sealing, to permit the activity experienced when the bathtub remains in usage. The sealant can split relatively early if you do not take into account this motion prior to sealing.
Additionally, ceramic coving or quadrant tiles can be made use of to edge the bath or shower tray. Plastic strips of coving, which are easy to use and also reduce to dimension, are likewise easily readily available on the market. It is recommended to fit the tiles using water-resistant or water resistant sticky and also cement.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
I hope you liked our post on How to Install a Bathtub: Install an Acrylic Tub and Tub Surround. Thanks a ton for taking the time to read through our article. Are you aware of someone else who is in the market for How to Install a Bathtub? Feel free to promote it. I enjoy reading our article about Tools You Need to Install a New Bathtub .
Hot water issues? Report this page